Substance use disorder means a cluster of cognitive, behavioral, and physiological symptoms indicating that an individual continues using the substance despite significant substance-related problems. Specified anatomical areas means and includes less than completely and opaquely covered human genitals, pubic region, buttocks, anus, female breasts below a point immediately above the top of the areolae, or human male genitals in a discernible turgid state, even if completely and opaquely covered. An Investment Entity located in a Non-Participating Jurisdiction and managed by another Financial Institution is also treated as a Passive NFE for purposes of the CRS. Passive NFE Under the CRS a “Passive NFE” means any NFE that is not an Active NFE. Insecticide fogger means any insecticide product designed to release all or most of its content, as a fog or mist, into indoor areas during a single application. Oppressive State means: Tibet Autonomous Region and the Provinces of Ado, Kham and U-Tsang Lower explosive limit means the lowest per cent by volume of a mixture of explosive gases in air that will propagate a flame at twenty-five degrees Celsius and atmospheric pressure. No terms or conditions other than those stated herein, and no agreement or understanding, oral or written, in any way purporting to modify this warranty shall be binding upon DuPont unless made in writing and signed by and authorized employee of DuPont. No representative, dealer or any other person is authorized to make or makes any warranty, representation or promise on behalf of DuPont with respect to such products. This is the only commercial product warranty made by DuPont for Corian® Quartz. This warranty is issued to the original owner of the structure into which product was installed and expires upon transfer of ownership of the structure to a third party or removal of the Corian® Quartz installation to another location. Accordingly, DuPont assumes no responsibility or obligation with respect to the selection of product for the installation or the design, engineering and construction of the installation. DuPont clearly sets out and identifies the performance parameters of Corian® Quartz in its literature and Technical Bulletins which are available on the website. Furthermore, laws and building and safety codes governing the design, engineering and construction of installations vary widely. In addition, DuPont shall not be responsible for any damage or injury caused in whole or in part by climate, job site condition, architectural and engineering design, structural movement, acts of vandalism, accident, war, or defective or improper workmanship by the fabricator or installer or any laborer, or any other damage or injury not solely and directly caused by defects in products covered by the warranty. “ Acts of nature” include, but are not limited to, exposure to the outdoors, weather effects and fire. Common sense should be exercised by using trivets when putting hot objects directly from a heat source onto the product or when exposing the product to heat. Cracking around a cooktop, hot tray, heat lamp or buffet top may appear by permitting cookware that is on or partially on heating elements to overhang the countertop or other heat source to cause excessive heat on the countertop or from using high temperatures for excessively lengthy periods of time. Training should follow Occupational Safety and Health Administration (OSHA) guidelines and state regulations.Įxcessive heat or cold may reduce vaccine potency, thereby increasing the risk that recipients will not be protected against vaccine- preventable diseases.Įxcessive heat means exposure to heat of such a degree that white marks, white rings or cracks appear on the product. STABILITY: Material is stable under normal conditions CONDITIONS TO AVOID: Excessive heat. The definition of peening, in accordance with the AWS Code is, “the mechanical working of metals using impact blows or hammer blows.” Excessive heat input during welding can also be detrimental to a weld.Ĭondition to avoid Excessive heat Dust formation Materials to avoidStrong oxidizers, which could vigorously oxidize organic materials in this mixture and cause a fire in an extreme case.Ĭonditions to Avoid: Excessive heat for prolonged periods of time.Įxcessive heat can result in grain damage, over-drying and potential grain fires. Excessive heat can cause premature aging of components resulting in a shorter shelf life.Įxcessive heat is defined as temperatures at or above 104 degrees Fahrenheit (104F).Įxcessive heat must be avoided (e.g., do not leave in direct sunlight or a closed-up car during summer).
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |